Toyota Ifs Steering Box Mount

1 Center the pitman arm. The kit is also useful for my application though since it comes with frame sleeves and a new mount that will make relocating the steering box much easier.

Ifs Steering Box Mount Kit

Obtain an IFS steering box from a 1986-1995 4wheel drive Pickup or 4Runner note 2wd steering box will not work.

Toyota ifs steering box mount. Both inner and outer frame reinforcing plates made of 14 steel and steel DOM frame tubes to prevent frame-crumpling. Pre 79 Ford Dana 44 Steering. Chevy Dana 44 Steering.

This frame mount kit includes both inner and outer frame reinforcing plates grade 8 bolts DOM tubing and Crimp nuts. 5 Remove Sector Shaft. IFS Steering Box Mount Kit.

Add to Wish List. Place steering box on frame rail and slide forward until it contacts body mount. This frame mount kit includes both inner and outer frame reinforcing plates grade 8 bolts DOM tubing and Crimp nuts.

Chevy Dana 60 Kingpin Steering. This frame mount kit includes both inner and outer frame reinforcing plates grade 8 bolts DOM tubing and Crimp nuts. I cut it long enough to run the steering box bolts through the part of the gusset against the frame and cut the back at a curve to avoid a perpenducular line of weld against the frame.

Remove stock steering box steering arms front axle anti wrap bar. Unbolt or cut off with a torch the factory push-pull steering box mount. Toyota Heavy Duty Steering Box Mount Kit.

The IFS steering boxes are better suited to high steer than the push-pull boxes on 79-85 Toyotas because the pitman arm swings side-to-side instead of front-to-back. Items 1-33 of 50. Inner plate is 316 outer plate is 14.

DOM Sleeves for inserting through frame. Chevy Axle. If youre installing crossover steering on your 79-85 4wd Toyota youre going to need to mount an IFS steering box.

Fits IFS box 86-95 on either a solid axle 79-85 truck 4 runner or factory IFS truck. IFS box – CounterClockWise. 1979-1995 Toyota Pickup Steering Stabilizer Kit.

Low Pressure Return Fitting for 86-95 Toyota Pickup4Runner IFS Steering B. View as Grid List. 6 Turn input shaft so internal piston moves toward input end.

Leaf Spring Frame Tubes for IFS to Leaf Spring Conversion. The Issue with Attaching High Steer. Drilling the holes for the frame sleeves.

This frame mount kit includes everything you need to mount a Toyota IFS Steering Box to your frame. Clamps see that are drilled out the length of the advice guys at this warranty replacement toyota ifs boxes. I used some emu springs off the rear of my 94 truck for my SAS which have the center pin way up front so my steering box had to crowd into the drivers front body mounts space to avoid smacking the tie rod on.

1979-1995 Toyota Pickup Steering Stabilizer Mount Kit. IFS Steering Box Mount If youre installing crossover steering on your 79-85 4wd Toyota youre going to need to mount an IFS steering box. Add to Wish List.

4 Remove top 4 bolts above sector shaft 14 mm. Rotate the steering box. Ford Axle.

Fitting 14 Pipe to 6 JIC. Plates are 14 and 316 material Dom sleeves are 34 OD 120 wall USA tube. 92-20 Ford Balljoint 60 Steering.

Inner plate is 14 outer plate is 316. Includes grade 8 12 hardware may require reaming steering box bolts holes slightly. 0 Remove and thoroughly clean outside of the steering box.

Coast gear mounting area where to keep the arms are drilled the gear and bearings. IFS Steering Box Mount If youre installing crossover steering on your 79-85 4wd Toyota youre going to need to mount an IFS steering box. Can also be used on anything utilizing a Toyota IFS box such as Classic Broncos.

Add to Wish List. No questions asked lifetime warranty. 3 Remove the pitman arm.

Angled leading and trailing edges prevent frame cracking. Inner plate is 14 outer plate is 316. My understanding that the FJ-80 box is also identical to the FJ556062 STEPS.

This kit is typically used by owners of 85 and older solid axle pickups when converting to crossover steering and the required IFS steering box. Install pitman arm onto steering box and snug down the sector shaft nut. Align it to match the steering column path I built a prototype bracket that would need to be welded to the frame but would also need to build an extension for the column and reverse the pitman arm so it faces forward ifs have reverse movement.

Toyota IFS Steering Box Mount Kit. 916-18 JIC -6 to M16-15 Adapter for IFS Steering Box. Toyota steering box mount instructions for this item is.

Chevy W 92-04 Ford BallJoint Dana 60. This is a standard swap item on early Toys. Take the box mount it between the upright fender support and the old box mounting bracket.

Fabbed same thickness of toyota ifs box plate into the sector shaft are installed. You need to adapt the high steer kit to your IFS box pitman arm. IFS Steering Box Mount.

Ifs Steering Box Placement Need To Rework It Pirate 4×4